Vadovas Makita PLM5113N2 Vejapjovė

Vadovas

12

Note: Engine brake (brake handle): Use the lever

to stop the engine. When you release the lever the engine

and the blade stop automatically. To mow, hold the lever in

the working position. Before you start to mow, check the

start/stop lever several times to be sure that it is working

properly. Ensure that the tension cable can be smoothly

operated (i.e. is not catching or kinking in any way).

7-4 TO STOP ENGINE

CAUTION: The blade continues to rotate for a

few seconds after the engine is shut off.

1. Release the stop control handle to stop the engine

and blade.

2. Disconnect and ground the spark plug wire as

instructed in the separate engine manual to prevent

accidental starting while equipment is unattended.

7-5 CONNECTION FOR AUTO MOVE

The mower is equipped with a speed adjusting system

which can adjust 3 speeds from 3.0 km/h to 4.5 km/h.

Position : the slowest position; Position : the

fastest position

The step as below:

1. Release the self-drive control handle until the lawn

mower doesn’t go forward.

2. Adjust the appropriate speed which you want.

(Fig. 22)

3. Grasp the self-drive control handle to go on mowing.

CAUTION: Your mower is designed to cut normal

residential grass of a height no more than 250 mm.

Do not attempt to mow through unusually tall dry or wet

grass (e.g., pasture) or piles of dry leaves. Debris may

build up on the mower deck or contact the engine exhaust

presenting a potential fire hazard.

7-6 FOR THE BEST RESULTS WHEN

MOWING

Clear lawn of debris. Be sure that the lawn is clear of

stones, sticks, wire or other foreign objects which could be

accidentally thrown out by the mower in any direction and

cause serious personal injury to the operator and others

as well as damage to property and surrounding objects.

Do not cut wet grass. For effective mowing do not cut wet

grass because it tends to stick to the underside of the

deck preventing proper mowing of the grass clippings. Cut

no more than 1/3 the length of the grass. The

recommended cut for mowing is 1/3 the length of the

grass. Ground speed will need to be adjusted so the

clippings can be dispersed evenly into the lawn. For

especially heavy cutting in thick grass it may be

necessary to use one of the slowest speeds in order to get

a clean well mowed cut. When mowing long grass you

may have to cut the lawn in two passes, lowering the

blade another 1/3 of the length for the second cut and

perhaps cutting in a different pattern than was used the

first time. Overlapping the cut a little on each pass will

also help to clean up any stray clippings left on the lawn.

The mower should always be operated at full throttle to

get the best cut and allow it to do the most effective job of

mowing. Clean underside of deck. Be certain to clean the

underside of the cutting deck after each use to avoid a

build-up of grass, which would prevent proper mulching.

Mowing leaves. The mowing of leaves can also be

beneficial to your lawn. When mowing leaves make sure

they are dry and are not laying too thick on the lawn. Do

not wait for all the leaves to be off the trees before you

mow.

WARNING: If you strike a foreign object, stop the

engine. Remove wire from spark plug, thoroughly inspect

the mower for any damage and repair the damage before

restarting and operating the mower. Extensive vibration of

the mower during operation is an indication of damage.

The unit should be promptly inspected and repaired.

7-7 GRASS CATCHER

Empty and clean the bag, make sure it is clean and

ensure its meshwork is ventilated. (Fig. 23)

7-8 DECK

The underside of the mower deck should be cleaned after

each use to prevent a buildup of grass clippings, leaves,

dirt or other matter. If this debris is allowed to accumulate,

it will invite rust and corrosion, and may prevent proper

mulching. The deck may be cleaned by tilting the mower

and scraping clean with a suitable tool (make certain the

spark plug wire is disconnected).

7-9 HEIGHT ADJUSTMENT

INSTRUCTIONS

CAUTION: Do not at any time make any

adjustment to lawn mower without first stopping the

engine and disconnecting the spark plug wire.

CAUTION: Before changing mowing height, stop

mower and disconnect spark plug cable.

Your mower is equipped with a central height adjustment

lever offering 5 height positions. (25 mm – 70 mm)

1. Stop mower and disconnect spark plug cable before

changing mower cutting height.

2. The central height adjustment lever offers you

5 different height positions. (Fig. 24)

3. To change the height of cut, squeeze adjuster lever

toward the wheel, moving up or down to selected

height. All wheels will be in the same height of cut.

8. MAINTENANCE

INSTRUCTIONS

SPARK PLUG

Use only original replacement spark plug. For best results,

replace the spark plug every 100 hours of use. (refer to

ENGINE OWNER’S MANUAL)

Įvertinimas

Daugiau apie šį vadovą

Suprantame, kad puiku turėti popierinį savo Makita PLM5113N2 Vejapjovė vadovą. Visada galite atsisiųsti vadovą iš mūsų svetainės ir atsispausdinti patys. Jei norite turėti originalų vadovą, rekomenduojame susisiekti su Makita. Jie gali pateikti originalų vadovą. Ar ieškote savo Makita PLM5113N2 Vejapjovė vadovo kita kalba? Pasirinkite pageidaujamą kalbą mūsų pagrindiniame puslapyje ir ieškokite modelio numerio, kad pamatytumėte, ar jį turime.

Specifikacijos

Visi Makita Vejapjovės vadovai
Daugiau Vejapjovės vadovų

Dažnai užduodami klausimai apie Makita PLM5113N2 Vejapjovė

Mūsų palaikymo komanda ieško naudingos informacijos apie produktą ir atsakymų į dažniausiai užduodamus klausimus. Jei dažniausiai užduodamuose klausimuose pastebėjote netikslumų, praneškite mums naudodamiesi mūsų kontaktų forma.

Susiję produktai

Vadovas

Makita ELM3700 Vejapjovė

Vadovas

Makita ELM4121 Vejapjovė

Vadovas

Makita PLM4601 Vejapjovė

Vadovas

Makita PLM4101 Vejapjovė

Vadovas

Makita PLM5100 Vejapjovė

Vadovas

Makita PLM5120N2 Vejapjovė

Vadovas

Makita PLM5101 Vejapjovė

Vadovas

Makita PLM4630N2 Vejapjovė

Susijusios kategorijos