Vadovas Greenworks GD24AG Kampinis šlifuoklis

Vadovas

WARNING

Examine the machine before you use. The machine must be

installed correctly and can move freely. Do a test to operate

for 1 minute with no load. Do not use damaged, out of

centre or vibration machine. Damaged machine can break

and cause injuries

4.3 ADJUST THE GUARD

Figure 6.

WARNING

Adjust the guard on the machine correctly refer to which

side you install the handle.

WARNING

Let the guard in front of the machine. If not, sparks and

loose pieces of the grinding wheel can cause injury to the

operator. Put the guard in the correct location.

1. Remove the battery pack.

2. Pull the guard clasp to unlock the guard.

3. Turn the guard to its correct position.

4. Push the guard clasp in to lock the guard.

NOTE

Make sure that you install the ridge on the guard in the

groove of the bearing cap.

4.4 REPLACE THE GUARD

WARNING

Do not change or loosen guard screw. Failure to follow this

warning can make the guard to become loose during

operation and cause injury.

After extended use, you must replace the guard. If you fall the

machine and cause damage the guard. It is also necessary for

you to replace the guard.

WARNING

To prevent loss of control and possible injury, operate the

machine with two hands and keep one hand on the auxiliary

handle.

• Remove the battery pack from the machine.

• Push the spindle lock.

• Use a wrench to loosen and remove clamp nut.

• Remove grinding wheel and disc flange.

• Pull the guard clasp to unlock the guard.

• Remove the guard from the groove in the housing.

• Put the new guard on the shoulder of the bearing cap.

• Adjust the guard to the correct position.

NOTE

Make sure you install the ridge on the guard in the groove

on the bearing cap.

• Install disc flange, grinding wheel, and clamp nut.

• Tighten the clamp nut.

4.5 OPERATE THE MACHINE

Use correct grinding wheels that are recommended for the

material. Make sure that the minimum speed of a accessory

wheel is 6,500 r/min. or more. The grinding wheel is correct

for grinding welds, preparing surfaces to be welded, grinding

structural steel, and grinding stainless steel.

CAUTION

Do not use the machine without the guard. Use the machine

without guard will cause injury to the operator.

NOTE

Make sure all work in a vise or clamp to a workbench.

1. Use two hands to hold the machine in front and away

from you and the workpices.

2. Start the grinder and let the engine and grinding wheel

increase to full speed.

3. Lower the grinder until the grinding wheel touches the

workpiece.

4. Keep the machine tilted at an angle from 5° to 15° and

move at a stable speed.

5. Use sufficient pressure to keep the machine stable.

6. Lift the machine away from the workpiece before you

stop the machine.

WARNING

To prevent loss of control and injury,operate the machine

with two hands and keep one hand on the auxiliary handle.

NOTE

If you put the machine in one point too long or hold the

machine at too sharp an angle, it will make grooves in the

workpiece.

NOTE

Heavy pressure decreases the speed and put a strain on the

engine. The weight of the machine is sufficient for most

grinding works. Use light pressure when you grind jagged

edges or loose bolts where there is the possible to stop the

machine on the metal edge.

5

English

EN

Įvertinimas

Daugiau apie šį vadovą

Suprantame, kad puiku turėti popierinį savo Greenworks GD24AG Kampinis šlifuoklis vadovą. Visada galite atsisiųsti vadovą iš mūsų svetainės ir atsispausdinti patys. Jei norite turėti originalų vadovą, rekomenduojame susisiekti su Greenworks. Jie gali pateikti originalų vadovą. Ar ieškote savo Greenworks GD24AG Kampinis šlifuoklis vadovo kita kalba? Pasirinkite pageidaujamą kalbą mūsų pagrindiniame puslapyje ir ieškokite modelio numerio, kad pamatytumėte, ar jį turime.

Specifikacijos

Visi Greenworks Kampiniai šlifuokliai vadovai
Daugiau Kampiniai šlifuokliai vadovų

Dažnai užduodami klausimai apie Greenworks GD24AG Kampinis šlifuoklis

Mūsų palaikymo komanda ieško naudingos informacijos apie produktą ir atsakymų į dažniausiai užduodamus klausimus. Jei dažniausiai užduodamuose klausimuose pastebėjote netikslumų, praneškite mums naudodamiesi mūsų kontaktų forma.

Susiję produktai

Vadovas

Greenworks G24AG Kampinis šlifuoklis

Vadovas

Bosch GWX 18V-10 PC Kampinis šlifuoklis

Vadovas

Bosch GWS 750 S Professional Kampinis šlifuoklis

Vadovas

Ryobi RAG18115-0 Kampinis šlifuoklis

Vadovas

Bosch EasyCut&Grind Kampinis šlifuoklis

Vadovas

Bosch GWS 700 Professional Kampinis šlifuoklis

Vadovas

Bosch GWX 13-125 S Kampinis šlifuoklis

Vadovas

Parkside PWS 125 G6 Kampinis šlifuoklis

Susijusios kategorijos