Vadovas GEV FMR 3286 FlammEx Dūmų detektorius

Vadovas

98

DGBFNLIESDKFINRUSGRESTLVLTPLPROSLOSKCZTRUA H

The smoke detector should be replaced if it is damaged or

if there is a fault indication that cannot be reset. It should be

replaced no later than 10 years after activation. The battery is

not replaceable.

Nb:

If the detector is exposed to excessive dust or water

over a prolonged period, this may trigger the alarm.

Use

You will hear a beep every time the button is pressed.

This button (Fig. 5.2) has a number of features:

• If the button is pressed briefl y (max. 2 seconds), when the

alarm is triggered or just before it is triggered, the alarm

signal is muted for 10 min. During this time, a short beep

will be heard every 35 seconds (reminder signal).

• A fault signal can be muted for 12 hours by pressing the

button briefl y (max. 2 seconds).

• To test the detector, press and hold the button for at least

3 seconds until a loud, intermittent alarm signal can be heard.

To reset, activate the test function (by pressing and holding the

button for at least 3 seconds until a loud, intermittent alarm

signal is heard) or remove the detector from the base for 10

seconds.

Exception: You cannot reset reset a fault signal indicating an

empty battery.

Test/Maintenance

When activated, the detector's test function is fully checked

in accordance with DIN EN 14606: battery test, electronic

smoke chamber test, electronics test, etc.. Testing should be

carried out at least once a year to comply with current regional

standards for smoke alarms (DIN 14676 in Germany). Press

and hold the button (Fig. 5.2) for at least 3 seconds) until a

loud, intermittent alarm signal (approx. 85 dB/3m) can be heard.

When necessary (usually about once a year), wipe the device

with a clean, dry cloth and carefully clean the outside with a

vacuum cleaner. Ensure that there is no furniture within a radius

of 0.5 m that could prevent smoke from being detected. If this

is the case, relocate the detector or move the relevant furniture.

The device continuously and automatically tests the electronics,

battery voltage and internal resistance, the smoke chamber,

etc. If necessary, sensitivity can be adjusted according to the

amount of dirt in the smoke chamber. The red LED (Fig. 5.3)

fl ashes briefl y every 35 seconds to indicate that the device is

operating correctly and activated.

Table of functions

No. Alarm signal Red LED Description Solution

1 Intermittent

alarm signal.

Flashes at the same time

as the audible alarm signal.

The detector's alarm is

triggered because smoke has

been detected.

If the alarm is triggered, it can be

muted for 10 min. by pressing the

button briefl y (max. 2 seconds).

2

Short signal

emitted every

35 seconds.

Two fl ashes alternating

with the audible signal

every 35seconds.

The alarm is muted for

10minutes.

The alarm can be muted by

removing the detector from its

base for 10 seconds or by using

the test function: press and hold

the button for at least 3 seconds

until a loud, intermittent alarm

signal can be heard.

3 No signal. Flashes every 17 seconds. The 24-hour alarm memory

will help you locate a

triggered detector.

The alarm memory can be

deactivated by removing the

detector from its base for

10seconds or using the test

function: press and hold the button

for at least 3 seconds until a loud,

intermittent alarm signal can be

heard.

4 Short signal

emitted every

35 seconds.

Two fl ashes alternating

with the audible signal

every 35 seconds.

Fault signal indicating that

the battery is empty or there

is a malfunction.

The fault signal can be muted by

removing the detector from its

base for 10seconds or using the

test function: press and hold the

button for at least 3 seconds until a

loud, intermittent alarm signal can

be heard.

If the fault recurs, the detector

must be replaced. If the fault signal

is triggered, the alarm can be

muted for 12 hours by pressing the

button briefl y (max. 2seconds).

Įvertinimas

Daugiau apie šį vadovą

Suprantame, kad puiku turėti popierinį savo GEV FMR 3286 FlammEx Dūmų detektorius vadovą. Visada galite atsisiųsti vadovą iš mūsų svetainės ir atsispausdinti patys. Jei norite turėti originalų vadovą, rekomenduojame susisiekti su GEV. Jie gali pateikti originalų vadovą. Ar ieškote savo GEV FMR 3286 FlammEx Dūmų detektorius vadovo kita kalba? Pasirinkite pageidaujamą kalbą mūsų pagrindiniame puslapyje ir ieškokite modelio numerio, kad pamatytumėte, ar jį turime.

Specifikacijos

Visi GEV Dūmų detektoriai vadovai
Daugiau Dūmų detektoriai vadovų

Dažnai užduodami klausimai apie GEV FMR 3286 FlammEx Dūmų detektorius

Mūsų palaikymo komanda ieško naudingos informacijos apie produktą ir atsakymų į dažniausiai užduodamus klausimus. Jei dažniausiai užduodamuose klausimuose pastebėjote netikslumų, praneškite mums naudodamiesi mūsų kontaktų forma.

Susiję produktai

Vadovas

GEV FMR 3033 FlammEx Dūmų detektorius

Vadovas

GEV FSR 4160 Dūmų detektorius

Vadovas

GEV FMR 3569 FlammEx Dūmų detektorius

Vadovas

GEV FMR 4023 FlammEx Dūmų detektorius

Vadovas

GEV FMR 3392 FlammEx Dūmų detektorius

Vadovas

Brennenstuhl RM C 9010 Dūmų detektorius

Vadovas

Deltaco SH-WS03 Dūmų detektorius

Susijusios kategorijos