Vadovas FERM MSM1040 Diskinis pjūklas

Vadovas

7

EN

versa is very dangerous.

• Do not reach behind the fence with either

hand closer than 100 mm from either side

of the saw blade, to remove wood scraps,

or for any other reason while the blade is

spinning. The proximity of the spinning saw

blade to your hand may not be obvious and you

may be seriously injured.

• Inspect your workpiece before cutting. If

the workpiece is bowed or warped, clamp

it with the outside bowed face toward the

fence. Always make certain that there

is no gap between the workpiece, fence

and table along the line of the cut. Bent or

warped workpieces can twist or shift and may

cause binding on the spinning saw blade while

cutting. There should be no nails or foreign

objects in the workpiece.

• Do not use the saw until the table is clear

of all tools, wood scraps, etc., except for

the workpiece. Small debris or loose pieces

of wood or other objects that contact the

revolving blade can be thrown with high speed.

• Cut only one workpiece at a time. Stacked

multiple workpieces cannot be adequately

clamped or braced and may bind on the blade

or shift during cutting.

• Ensure the mitre saw is mounted or placed

on a level, firm work surface before use. A

level and firm work surface reduces the risk of

the mitre saw becoming unstable.

• Plan your work. Every time you change the

bevel or mitre angle setting, make sure the

adjustable fence is set correctly to support

the workpiece and will not interfere with

the blade or the guarding system. Without

turning the tool “ON” and with no workpiece

on the table, move the saw blade through a

complete simulated cut to assure there will be

no interference or danger of cutting the fence.

• Provide adequate support such as table

extensions, saw horses, etc. for a workpiece

that is wider or longer than the table top.

Workpieces longer or wider than the mitre saw

table can tip if not securely supported. If the

cut-off piece or workpiece tips, it can lift the

lower guard or be thrown by the spinning blade.

• Do not use another person as a substitute

for a table extension or as additional

support. Unstable support for the workpiece

can cause the blade to bind or the workpiece

to shift during the cutting operation pulling you

and the helper into the spinning blade.

• The cut-off piece must not be jammed or

pressed by any means against the spinning

saw blade. If confined, i.e. using length stops,

the cut-off piece could get wedged against the

blade and thrown violently.

• Always use a clamp or a fixture designed

to properly support round material such as

rods or tubing. Rods have a tendency to roll

while being cut, causing the blade to “bite” and

pull the work with your hand into the blade.

• Let the blade reach full speed before

contacting the workpiece. This will reduce the

risk of the workpiece being thrown.

• If the workpiece or blade becomes jammed,

turn the mitre saw off. Wait for all moving

parts to stop and disconnect the plug

from the power source and/or remove the

battery pack. Then work to free the jammed

material. Continued sawing with a jammed

workpiece could cause loss of control or

damage to the mitre saw.

• After finishing the cut, release the switch,

hold the saw head down and wait for the

blade to stop before removing the cut-off

piece. Reaching with your hand near the

coasting blade is dangerous.

• Hold the handle firmly when making an

incomplete cut or when releasing the switch

before the saw head is completely in the

down position. The braking action of the saw

may cause the saw head to be suddenly pulled

downward, causing a risk of injury.

• Keep your work area clean. Material mixtures

are particularly hazardous. Light metal dust

may catch fire or explode.

• Do not use dull, cracked, bent or damaged

saw blades. Unsharpened or improperly set

saw blades produce narrow kerf causing

excessive friction, blade binding and

kickback.

• Do not use saw blades made from high speed

steel (HSS). Such saw blades can easily break.

• Always use saw blades with correct size

and shape (diamond versus round) of arbour

holes. Saw blades that do not match the

mounting hardware of the saw will run off-centre,

causing loss of control.

• Do not replace the integrated laser with

a laser of another type. A laser that is not

Įvertinimas

Daugiau apie šį vadovą

Suprantame, kad puiku turėti popierinį savo FERM MSM1040 Diskinis pjūklas vadovą. Visada galite atsisiųsti vadovą iš mūsų svetainės ir atsispausdinti patys. Jei norite turėti originalų vadovą, rekomenduojame susisiekti su FERM. Jie gali pateikti originalų vadovą. Ar ieškote savo FERM MSM1040 Diskinis pjūklas vadovo kita kalba? Pasirinkite pageidaujamą kalbą mūsų pagrindiniame puslapyje ir ieškokite modelio numerio, kad pamatytumėte, ar jį turime.

Specifikacijos

Visi FERM Diskiniai pjūklai vadovai
Daugiau Diskiniai pjūklai vadovų

Dažnai užduodami klausimai apie FERM MSM1040 Diskinis pjūklas

Mūsų palaikymo komanda ieško naudingos informacijos apie produktą ir atsakymų į dažniausiai užduodamus klausimus. Jei dažniausiai užduodamuose klausimuose pastebėjote netikslumų, praneškite mums naudodamiesi mūsų kontaktų forma.

Susiję produktai

Vadovas

FERM MSM1035 Diskinis pjūklas

Vadovas

FERM CSM1019 Diskinis pjūklas

Vadovas

FERM MSM1038 Diskinis pjūklas

Vadovas

FERM COM1007P Diskinis pjūklas

Vadovas

FERM CSM1039 Diskinis pjūklas

Vadovas

FERM MSM1039 Diskinis pjūklas

Vadovas

Scheppach HM254 Diskinis pjūklas

Vadovas

Skil 3551 AB Diskinis pjūklas

Susijusios kategorijos