Vadovas FERM MSM1035 Diskinis pjūklas

Vadovas

7

EN

(RCD) protected supply. Use of an RCD

reduces the risk of electric shock

Mechanical

a) Before you start the machine, check if the saw

blade is allowed to rotate freely. Check in every

different position of the saw machine if the saw

blade revolves freely, if the saw blade touches

anything the machine must be adjusted or

repaired.

b) Do not use the power tool if the switch does

not turn on and off. A power tool that cannot

be controlled with the switch is dangerous and

must be repaired.

c) Always use saw blades with the correct size

and shape. Use saw blades recommended

by the manufacture (EN-847-1). Saw blades

that do not match the mounting hardware of

the saw will run eccentrically, causing loss of

control. Only buy saw blades with a suitable

number of revolutions of at least 4500 RPM

d) Never use too small or too big saw blades.

This is very dangerous

e) Never remove marking on saw blade. Technical

information must always visible to make the

right choices by exchanging the saw blade

f) Secure the work piece. Always clamp work

piece with clamping devices, this is much safer

than by hand

g) Never leave the machine before the complete

stopped

h) Do not use High speed steel saw blades (HSS).

Saw blade can easily break

i) Do never use dull, cracked, bent or damaged

saw blades. Before use pull the mains plug

and check the saw blade. Damaged or

unsharpened saw blades produce narrow kerf,

excessive friction, blade binding and kickback.

Exchange damaged saw blades immediately,

always use original flenses, nut and/ or bolts.

j) Remove any adjusting key or wrench before

turning the power tool. A wrench or a key

left attached to a rotating part of the power

tool may result in a personal injury and very

dangerous situation

k) The arrow marked on the saw blade, which

indicates the direction of rotation. Must point

in the same direction as the arrow marked on

the machine, the saw blade teeth must point

downwards on the front of the saw

l) Do not touch the saw blade after work before it

has cooled. The saw blade becomes very hot

while working

m) Protect the saw blade from strikes and shocks.

Do not apply side pressure to the saw blade

n) Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at

the rate which it was signed

o) Never stand on the power tool. Serious injury

can occur when the power tool tips over.

Always use extra support for more stability of

the machine

p) Machine is provided with devices for the

connection of dust extraction, ensure these

are connected and properly used. Dust

collection reduce dust- related hazard’s

q) Maintain the air outlets at the machine. Dust

must be removed.

r) Make sure that the guard operates properly

and that it can move freely. Never lock the

guard in place when opened

s) Never remove cutting remainders from the

sawing area while the machine is running.

Always guide the tool arm back to the neutral

position first and then switch the machine off

t) Guide the saw blade against the work piece

only when the machine is switched on.

Otherwise there is a risk of a kickback, when the

saw blade becomes wedged in the work piece

u) If the saw blade should become jammed.

Switch the machine off and hold the work piece

until the saw blade comes to a complete stop

v) To prevent a kick back. The work piece may not

be moved until after the machine has complete

stopped. Correct the cause for the jamming of

the saw blade before restarting the machine

w) When sawing profile sections, round pieces or

other pieces, always press the piece of work

against the stop and can’t move, so it cannot

till or turn or move while sawing.

x) Never use the machine to saw pieces of work

that are to small that they cannot be secured

safely. Small pieces of wood or other objects

that come in contact with the rotating saw blade

can strike the operator or out standers with high

speed

y) When sawing always use the additional supports

z) For sawing of large piece work that not

supported. Use extra supports

Įvertinimas

Daugiau apie šį vadovą

Suprantame, kad puiku turėti popierinį savo FERM MSM1035 Diskinis pjūklas vadovą. Visada galite atsisiųsti vadovą iš mūsų svetainės ir atsispausdinti patys. Jei norite turėti originalų vadovą, rekomenduojame susisiekti su FERM. Jie gali pateikti originalų vadovą. Ar ieškote savo FERM MSM1035 Diskinis pjūklas vadovo kita kalba? Pasirinkite pageidaujamą kalbą mūsų pagrindiniame puslapyje ir ieškokite modelio numerio, kad pamatytumėte, ar jį turime.

Specifikacijos

Visi FERM Diskiniai pjūklai vadovai
Daugiau Diskiniai pjūklai vadovų

Dažnai užduodami klausimai apie FERM MSM1035 Diskinis pjūklas

Mūsų palaikymo komanda ieško naudingos informacijos apie produktą ir atsakymų į dažniausiai užduodamus klausimus. Jei dažniausiai užduodamuose klausimuose pastebėjote netikslumų, praneškite mums naudodamiesi mūsų kontaktų forma.

Susiję produktai

Vadovas

FERM MSM1038 Diskinis pjūklas

Vadovas

FERM MSM1039 Diskinis pjūklas

Vadovas

FERM CSM1019 Diskinis pjūklas

Vadovas

FERM MSM1040 Diskinis pjūklas

Vadovas

FERM CSM1039 Diskinis pjūklas

Vadovas

FERM COM1007P Diskinis pjūklas

Vadovas

Parkside IAN 315014 Diskinis pjūklas

Vadovas

FEMI TR 235 Diskinis pjūklas

Susijusios kategorijos