Vadovas Camry CR 1289 Virdulys

Vadovas

11 When the water is heated to the appropriate temperature, device signals this with three beeps. If the kettle is not removed from the

base, after a few minutes a beep will be repeated.

10. Switching empty kettle, or with insufficient level of water, will cause automate switching off the kettle. Wait till cool down the kettle,

pour enough water and after few minutes switch the kettle on.

Press “A” key briefly, the buzzer will send out a “di” sound, the kettle is boiling now.

WATER BOILING 60℃ - 90℃ WITHOUT THE KEEP WARM FUNCTION

BASICAL OPERATION:

After the water boils, indicator turns off and the buzzer sends out a “di” sound at the same time.

13. The kettle is an electrical device and it is not designed to hold water or other liquids. After boiling, the water must be immediately

pour into another bowl. The water in the kettle after boiling can not stay longer than 10 minutes. Before each use, fill the kettle with

fresh water above the minimum and below the maximum level.

SINGLE BOILING UP TO 100℃

9. Regularly remove limestone sediment inside the kettle. Sediment may cause overheating of the kettle, shorten life cycle and cancel

guarantee. Use mixings available in household stores or apply citric acid.

8. After boiling, time demanded for the thermostat to be ready is 2 minutes. After this time kettle can be switched on again.

12.The beep sound warns user when the device is not on the basis of, or is not put properly.

Press the “A” key briefly, with the sound “di.”, it starts working.

Press“B” key once / twice / thrice / the fourth time, then the indicator light is under 60℃ / 70℃ / 80℃ / 90℃ condition with green / blue /

yellow / purple LED light. This means that it will stop heating when the water temperature reaches 60℃ / 70℃ / 80℃ / 90℃

KEEP WARM FUNCTION 100℃

Press “A” for 2 seconds, with the buzzer sends out “di” sound, “B” button indicator light is on, and the kettle is in keep warm mode, with red

LED light will switch on. The indicator light is still lit after water has finished the boiling and the kettle automatically turns in the keep warm

function for 2 hours. When the water temperature decreases to 85℃ the kettle starts to boil again to 100℃ and repeat the operation for 2

hours.

ADVANCED OPERATION:

4. After boiling water the kettle will automatically switch off.

5. Before taking the kettle out of the base make sure it is switched off.

24. Never use kettle without filter or with open cover (automatic shutdown will not work).

2. Place the appliance on the flat, even and heat resistant surface.

7. Keep lid closed during boiling process. Or the kettle won't automatically switch off.

1. Fill the kettle with water. Make sure that heating plate is fully immersed in water.

28. Do not wash the base of the kettle directly in the water, just wipe with a dry cloth.

6. The kettle can manually be switched off in any time by ON/OFF switch.

22. Never fill kettle above MAX level and below MIN level. It may cause damage of kettle.

25. Descale your kettle regularly. Using kettle with heating element covered by scale may

cause damage.

DESCRIPTION

1 - plastic lid 2 - lid opening switch 3 - housing

lid. Do not open the lid during boiling in kettle or immediately after boiling, because steam

coming out of lid can cause burns.

26. Do not use aggressive detergents to wash the kettle housing - they can damage the

kettle or remove the markings.

29. Children aged 3 to 8 years old can enable and disable the device only when it is in its

normal position of use, they are supervised or instructed on the safe use and understand

the resulting risks. Children aged 3 to 8 years old can not connect device, operate, clean

or maintain.

21. Move the kettle only by holding it by handle..

4 - handle 5 - base 6 - anti-calc filter 7 - control panel

23. Never switch on kettle without water.

USING THE ELECTRIC KETTLE

BEFORE FIRST USE: Fill up the kettle with water, boil and pour. Repeat three times. To remove possible scent of manufactory, please

boil few times water.

3. Plug the kettle to the 220-240V ~50/60Hz mains, press ON/OFF switch. Indicator lamp will light.

27. The device is not designed to work with external schedulers or separate remote

control system.

4

Įvertinimas

Daugiau apie šį vadovą

Suprantame, kad puiku turėti popierinį savo Camry CR 1289 Virdulys vadovą. Visada galite atsisiųsti vadovą iš mūsų svetainės ir atsispausdinti patys. Jei norite turėti originalų vadovą, rekomenduojame susisiekti su Camry. Jie gali pateikti originalų vadovą. Ar ieškote savo Camry CR 1289 Virdulys vadovo kita kalba? Pasirinkite pageidaujamą kalbą mūsų pagrindiniame puslapyje ir ieškokite modelio numerio, kad pamatytumėte, ar jį turime.

Specifikacijos

Visi Camry Virduliai vadovai
Daugiau Virduliai vadovų

Dažnai užduodami klausimai apie Camry CR 1289 Virdulys

Mūsų palaikymo komanda ieško naudingos informacijos apie produktą ir atsakymų į dažniausiai užduodamus klausimus. Jei dažniausiai užduodamuose klausimuose pastebėjote netikslumų, praneškite mums naudodamiesi mūsų kontaktų forma.

Susiję produktai

Vadovas

Camry CR 1253 Virdulys

Vadovas

Camry CR 1239 Virdulys

Vadovas

Camry CR 1251w Virdulys

Vadovas

Camry CR 1344 Virdulys

Vadovas

Camry CR 1300 Virdulys

Vadovas

Camry CR 1294 Virdulys

Vadovas

Camry CR 1269b Virdulys

Vadovas

Camry CR 1278 Virdulys

Susijusios kategorijos