Vadovas BEKO EV 6100 Skalbimo mašina

Vadovas

3 - EN

kilograms. Place the product on a solid and flat

floor that has sufficient load carrying capacity!

• Donotplacetheproductonthepowercable.

• Donotinstalltheproductatplaceswhere

temperaturemayfallbelow0ºC.

• Placetheproductatleast1cmawayfromthe

edges of other furniture.

Removing packaging reinforcement

Tiltthemachinebackwardstoremovethe

packaging reinforcement. Remove the packaging

reinforcementbypullingtheribbon.

Removing the transportation locks

A

Donotremovethetransportationlocksbefore

taking out the packaging reinforcement.

A

Removethetransportationsafetyboltsbefore

operating the washing machine! Otherwise, the

productwillbedamaged.

Loosenalltheboltswithasuitablespanneruntil

they rotate freely (C). Remove transportation safety

boltsbyturningthemgently.Attachtheplastic

coverssuppliedintheUserManualbagintothe

holes on the rear panel. (P)

C

 Keepthetransportationsafetyboltsinasafe

place to reuse when the washing machine

needstobemovedagaininthefuture.

C

Never move the product without the

transportationsafetyboltsproperlyfixedin

place!

Connecting water supply

C

 Thewatersupplypressurerequiredtorun

theproductisbetween1to10bars(0.1–10

MPa).Itisnecessarytohave10–80litersof

water flowing from the fully open tap in one

minute to have your machine run smoothly.

Attach a pressure reducing valve if water

pressure is higher.

C

 Ifyouaregoingtousethedoublewater-inlet

product as a single (cold) water-inlet unit, you

must install the supplied stopper to the hot

watervalvebeforeoperatingtheproduct.

(Appliesfortheproductssuppliedwithablind

stopper group.)

C

 Ifyouwanttousebothwaterinletsofthe

product, connect the hot water hose after

removing the stopper and gasket group from

the hot water valve. (Applies for the products

suppliedwithablindstoppergroup.)

A

Modelswithasinglewaterinletshouldnotbe

connectedtothehotwatertap.Insuchacase

the laundry will get damaged or the product will

switch to protection mode and will not operate.

A

Donotuseoldorusedwaterinlethoseson

thenewproduct.Itmaycausestainsonyour

laundry.

1. Connect the special hoses supplied with the

product to the water inlets on the product. Red

hose(left)(max.90ºC)isforhotwaterinlet,

bluehose(right)(max.25ºC)isforcoldwater

inlet.

A

Ensure that the cold and hot water connections

are made correctly when installing the product.

Otherwise, your laundry will come out hot at the

end of the washing process and wear out.

Tightenallhosenutsbyhand.Neveruseawrench

when tightening the nuts. Open the taps completely

after making the hose connection to check

forwaterleaksattheconnectionpoints.Ifany

leaks occur, turn off the tap and remove the nut.

Retighten the nut carefully after checking the seal.

To prevent water leakages and damages caused

bythem,keepthetapsclosedwhenthemachine

is not in use.

Connecting to the drain

• Theendofthedrainhosemustbedirectly

connected to the wastewater drain or to the

washbasin.

A

Yourhousewillbefloodedifthehosecomes

out of its housing during water discharge.

Moreover, there is risk of scalding due to

high washing temperatures! To prevent such

situations and to ensure smooth water intake

and discharge of the machine, fix the end of the

discharge hose tightly so that it cannot come

out.

• Thehoseshouldbeattachedtoaheightofat

least 40 cm, and 100 cm at most.

• Incasethehoseiselevatedafterlayingiton

the floor level or close to the ground (less than

40cmabovetheground),waterdischarge

becomesmoredifficultandthelaundrymay

come out excessively wet. Therefore, follow the

heightsdescribedinthefigure.

• Topreventflowingofdirtywaterbackintothe

machine and to allow for easy discharge, do

not immerse the hose end into the dirty water

ordonotdriveitinthedrainmorethan15cm.

Ifitistoolong,cutitshort.

• Theendofthehoseshouldnotbebent,it

shouldnotbesteppedonandthehosemust

notbepinchedbetweenthedrainandthe

machine.

• Ifthelengthofthehoseistooshort,useit

byaddinganoriginalextensionhose.Length

ofthehosemaynotbelongerthan3.2m.

Įvertinimas

Daugiau apie šį vadovą

Suprantame, kad puiku turėti popierinį savo BEKO EV 6100 Skalbimo mašina vadovą. Visada galite atsisiųsti vadovą iš mūsų svetainės ir atsispausdinti patys. Jei norite turėti originalų vadovą, rekomenduojame susisiekti su BEKO. Jie gali pateikti originalų vadovą. Ar ieškote savo BEKO EV 6100 Skalbimo mašina vadovo kita kalba? Pasirinkite pageidaujamą kalbą mūsų pagrindiniame puslapyje ir ieškokite modelio numerio, kad pamatytumėte, ar jį turime.

Specifikacijos

Visi BEKO Skalbimo mašinos vadovai
Daugiau Skalbimo mašinos vadovų

Dažnai užduodami klausimai apie BEKO EV 6100 Skalbimo mašina

Mūsų palaikymo komanda ieško naudingos informacijos apie produktą ir atsakymų į dažniausiai užduodamus klausimus. Jei dažniausiai užduodamuose klausimuose pastebėjote netikslumų, praneškite mums naudodamiesi mūsų kontaktų forma.

Susiję produktai

Vadovas

BEKO WMB 61022 M Skalbimo mašina

Vadovas

BEKO WMD 25106 T Skalbimo mašina

Vadovas

BEKO WRE 7512 XAW Skalbimo mašina

Vadovas

BEKO WKB 51231 M Skalbimo mašina

Vadovas

BEKO WRE6511WBD Skalbimo mašina

Vadovas

BEKO WKB 51231 PTM Skalbimo mašina

Vadovas

BEKO WML 15065 D Skalbimo mašina

Vadovas

BEKO EV 6800 Skalbimo mašina

Susijusios kategorijos